Xerox Phaser 6250DP: automatic two-sided color with 600 included sheets review

DP includes the duplex hardware for ordinary color reports

The Xerox Phaser 6250DP is the automatic two-sided member of this older color laser family with the standard two-source paper arrangement. Its 500-sheet main tray and 100-sheet MPT provide 600 nominal sheets, while USB 2.0 and 10/100 Ethernet offer documented compatible computer connections.

The original US configuration table includes automatic duplex on DP, alongside 256 MB memory. It lists a hard drive separately. That makes two-sided reports a standard hardware capability, while protected stored jobs remain an optional arrangement requiring additional equipment.

Choose paper for the actual duplex route

Ordinary Letter, Legal and A4 are supported by the standard sources and established for automatic two-sided output. The dedicated duplex instructions limit ordinary media to 65–163 gsm through the MPT and 65–130 gsm through the main tray. A heavier sheet accepted through one path is not automatically suitable for the other.

The same table separately permits specified glossy coated paper at 120–163 gsm and thin card in that range through the MPT. Follow the exact category rather than generalizing those entries to arbitrary specialty stock. Labels and envelopes are excluded from automatic duplex.

The nominal input count has no precise gsm basis established in the read table. Load within the physical fill limits, especially when using thicker stock. Match the panel paper type to the loaded material and select the intended source in the driver, because a correct size setting alone does not establish a suitable fuser setting.

Set orientation and binding before a long run

The original automatic-duplex sequence combines paper loading, source selection, page orientation and a two-sided driver setting. Its illustrations show separate paper paths from the MPT and main drawers. For preprinted or punched material, use the matching loading diagram instead of assuming the one-sided orientation remains appropriate.

Binding controls determine whether the finished pages turn along a long or short edge. The manual illustrates both portrait and landscape arrangements, with side-edge and top-edge binding. A short trial document is useful for confirming the intended reading direction before sending a complete report.

The historical Windows instructions name the relevant duplex choices in compatible Xerox drivers. Driver availability for a particular current computer still needs checking. A generic menu or an unsupported replacement driver should not be assumed to preserve every documented finishing choice.

Separate envelope work from automatic duplex

Supported envelopes use the MPT only, with no more than ten loaded at once. The original instructions place the printable side down and the flap to the right when viewed from the front. Choose a suitable laser paper envelope without windows or metal clasps and select its matching size, type and MPT source.

Use one-sided output for that job. The ordinary main tray's Legal capacity and the DP's duplex unit do not authorize a different envelope path. An occasional small envelope run is a distinct setup from the ordinary two-sided paper stack.

Verify installed options and computer connectivity

Both DP and N include USB, 10/100 Ethernet and a separately documented legacy parallel port. Ethernet is wired and is not gigabit. Configure the address and use suitable computer software; the read historical material does not establish native AirPrint or Mopria for a phone workflow.

Secure, Proof and Saved jobs need the optional internal hard drive. Secure Print uses a four-digit numeric job password followed by panel release, and the protected job is deleted after printing. Other disk-held jobs may survive power-off. The 256 MB memory declaration alone is not evidence that this disk-backed function is installed.

Extra 500-sheet and 1,000-sheet feeder assemblies are optional and cannot be stacked with one another. The DP therefore should not inherit the extra drawers or hard drive of other family configurations. It is also print-only: the color engine's single-pass description supplies no scanner, copy function or fax.

Assess the older machine using the right declarations

The original rate is up to 26 Letter pages per minute in color or black-and-white, compared with 24 A4. It is a one-sided manufacturer declaration, not a measured result or duplex throughput. A 100,000-page duty figure is separate from recommended monthly volume, which remains unestablished.

The US supply sheet declares standard black and each color at 4,000 pages or high-capacity versions at 8,000 each, based on approximately 5% coverage on an A-size page. Those replacement declarations do not establish starter yield or ISO/IEC 19798 results. Imaging, transfer and voltage-specific fuser items need separate attention.

The US DP part is listed as 110 V. Check the actual label, service condition and compatible software, and leave room for paper loading and maintenance covers. Exact US DP body measurements remain unestablished in the read sections; measure the particular configuration before planning a tight space.